Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - ArmedTexan

Pages: [1] 2 3 4 ... 50
General Gun Discussion / Re: Gun range dumbazz
« on: October 11, 2018, 07:41:41 PM »
Yes I saw this on the local Houston news. Just happened this past weekend.

Politics, Gripes, Complaints / Re: ..stand by to be turned to SALT..
« on: October 10, 2018, 07:25:18 PM »
Liberalism is a mental disorder! Sorry founding fathers this country that you created isnít recognizable anymore.

I bought a OC holster for my Browning High Power.

That was less than a mile from my house.

I carry a makarov chambered in 9x18, but at home Iím always just feet from a 9x19, .40 cal, .45. The best caliber is the one you can hit $h!t with. Iím pretty good with any caliber.

Shot the M&P 9.

General Gun Discussion / Re: Tomball VFW Gunshow.
« on: September 21, 2018, 06:24:17 PM »
Might have to take a look, not sure Iíll sale or buy anything.

Sociology professor enough said, every single sociology or philosophy professor that Iíve know or heard of has be a communist.

General Gun Discussion / Re: Do yo rmember your 1st gun.
« on: September 04, 2018, 07:19:45 PM »
My first gun that I shot was a Remington 870 in 20 gauge, I think I was 10 or 11 years old. Both of my kids first gun was a single shot .22 LR when they were 7 years old.

I have forgotten to put hear protection on before shooting a couple of times. Like Tango stated. It really didnít bother me, only a slight ring for a few hours. I donít remember the actual guns but it was one of my World War II 30 cal rifle and a couple with a 9mm handguns. I just canít hear women very much anymore  :th_thicon_idea:

In July, I noticed a man walked in the whataburger in Tomball openly carrying. No one seemed to notice but me.

Politics, Gripes, Complaints / Re: endangered species..
« on: August 25, 2018, 09:45:21 PM »
So sad...

So sad...

I feel so bad...

I feel so horrible that I once voted for that POS! Good riddance!

General Gun Discussion / Re: Hoppes #9
« on: August 07, 2018, 09:10:40 AM »
Thatís a good boy you got there, my son said the same thing before. I told my wife if I was single my house would smell of gun oils! She hates the smell.

General Gun Discussion / Re: Need help with my Tokarev
« on: August 04, 2018, 08:48:55 PM »
So how was that Enfield of yours? Hoping all was ok!

I like several songs from Def Leppard. Most of their biggest hits were from the 80s. But I enjoy rock and country music from the 60s the most.

General Gun Discussion / Re: Need help with my Tokarev
« on: August 03, 2018, 12:04:38 PM »
I thought about removing the safety, looked it up on YouTube, doesnít seem very difficult but the only problem that I see after the safety is removed is that there is a hole on the side of the frame. If there was something (a screw or a pin) to fill the hole I would remove it. Mine is also a range gun and I never set the safety on.

General Gun Discussion / Re: Need help with my Tokarev
« on: August 03, 2018, 08:53:01 AM »
Unfortunately mine does have a aftermarket safety. I like the Yugo models more than the other countries because itís magazine holds a extra round.

General Gun Discussion / Re: Need help with my Tokarev
« on: August 02, 2018, 09:35:39 PM »
OK, so after thinking about your post for about 10 minutes I disassembled my Tokarev. I just took the pin out and put it back in with a punch. It took me all of 5 mins, it took a little patience to make sure that the swivel was centered and with a couple of light hits it fell back into place. Good luck.

General Gun Discussion / Re: Need help with my Tokarev
« on: August 02, 2018, 09:13:41 PM »
I never had a problem with surplus 7.62x25 on my Yugo M57 (and my surplus was made in the 1950s). Replacing the pin and the swivel shouldnít be too hard. Sorry that you had such a bad experience with that ammo.

General Gun Discussion / Re: ..3D Printer firearms..
« on: July 31, 2018, 04:29:30 PM »
A lot online sources are freaking out about the so-called ďundetectable and untraceable plastic 3D ghost gunsĒ (not surprisingly). Some mention that the gun must have some metal parts like the firing pin for example, but only with a sentence or two. However no one, zero, nada, media sources are reporting that bullets are made out of different metals. Which I would think be detectable by a metal detector.

The foolish argument that the media repeats over and over about how 3D printers now allow criminals, mentality ill, etc to now obtain guns...fails to report that anyone can build a gun with parts found from a hardware store if you really wanted too. Criminals have built guns while in their jail cell, just go down to Huntsville, the prison museum there displays several of the confiscated guns and other weapons.   

I think that plastic guns made from a 3D printer isnt really going to be a problem. Sounds like the crazy fear of the plastic Glock, when it first appeared on the market.

Pages: [1] 2 3 4 ... 50